---

name: "cipp-standards" description: "CIPP's tenant-baseline enforcement model: the Report/Alert/Remediate standards modes and how to roll them out, on-demand standards evaluation, Best Practice Analyser reports, and SPF/DKIM/DMARC domain health results with their remediation actions." when_to_use: >- When auditing standards compliance, running BPA reports, checking domain authentication health, or detecting tenants drifting from configured baselines. Use when: cipp standards, bpa, best practice analyser, best practice analyzer, run standards check, domain health, dmarc, dkim, spf, tenant baseline, compliance drift, or secure score.

CIPP Standards & BPA

Standards are CIPP's mechanism for declaring "this is what every tenant we manage should look like" and continuously enforcing it. The Best Practice Analyser (BPA) is the read side — it shows you where current tenant state diverges from CIPP's recommended baseline. Domain health is a complementary check focused on email authentication.

Anti-triggers

• Drift against an Inforcer baseline — Inforcer and CIPP both say "baseline", "drift", and "secure score" but measure different things against different templates; a tenant can be CIPP-compliant and Inforcer-drifted at once. Use inforcer-baseline-alignment.
• Inspecting Conditional Access policies — CA policies are not CIPP standards and do not appear in BPA output; use cipp-security.
• Triaging what an Alert-mode standard actually raised — the queue those alerts land in is cipp-alerts.
• Drift measured across more than the CIPP-managed estate — the cross-vendor method for comparing tenants to a baseline and deciding what to remediate is compliance-pack-standards-drift; this skill is the CIPP standards engine it reads.

Tools

cipp_list_standards

cipp_list_standards(tenantFilter='contoso.onmicrosoft.com')

Returns the list of standards configured for the tenant: which standards are enabled, what action each takes (Report, Alert, Remediate), and current compliance status. Use tenantFilter='allTenants' for a portfolio-wide view.

cipp_run_standards_check

cipp_run_standards_check(tenantFilter='contoso.onmicrosoft.com')

Triggers an on-demand standards evaluation. CIPP runs this on a schedule, but force a fresh run after deploying a new standard or remediating a finding to confirm the fix took.

cipp_list_bpa

cipp_list_bpa(tenantFilter='contoso.onmicrosoft.com')

Returns the latest Best Practice Analyser report — every CIPP-recommended check with Pass/Fail/Warn status across categories (Security, Identity, Mail, SharePoint, Teams, Intune). The most useful single call for tenant health.

cipp_list_domain_health

cipp_list_domain_health(tenantFilter='contoso.onmicrosoft.com')

Per-domain SPF, DKIM, DMARC, MX, and DNSSEC results. Run for any tenant where mail authentication is suspect or before/after migrating mail.

Standards model

A "standard" in CIPP has three modes:

Mode	Behavior
Report	Check only; show in BPA
Alert	Check + raise alert when out of compliance
Remediate	Check + auto-fix when out of compliance

The progression for an MSP rolling out a new baseline is typically Report → Alert → Remediate over weeks, with the longest dwell in Alert to validate that auto-remediation will be safe.

Workflow patterns

Tenant health snapshot

bpa = cipp_list_bpa(tenantFilter)
fails = [check for check in bpa if check['status'] == 'Fail']
domain = cipp_list_domain_health(tenantFilter)
broken_dmarc = [d for d in domain if d.get('dmarcPass') is not True]

A tenant with > 5 BPA failures or any broken DMARC needs a remediation plan, not just a report.

Standards drift detection

all_tenants_standards = cipp_list_standards(tenantFilter='allTenants')

Compare the standards each tenant has enabled against the MSP's master baseline list. Tenants missing a baseline standard usually mean the standard was deployed after the tenant onboarded and never backfilled.

Pre-change validation

Before you change a tenant's identity or mail config:

1. cipp_list_bpa — capture current state
2. Make the change
3. cipp_run_standards_check to force a fresh evaluation
4. cipp_list_bpa again — diff against pre-change capture

Domain health interpretation

Result	Meaning	Action
SPF: missing	No SPF record at all	Add v=spf1 include:spf.protection.outlook.com -all
SPF: too many lookups	Record exceeds 10-DNS-lookup limit	Flatten or consolidate include: directives
DKIM: not configured	Default DKIM signing disabled	Enable in Defender / Exchange Admin
DMARC: p=none	Reporting only, no enforcement	Move to p=quarantine after monitoring
DMARC: missing	No DMARC record	Add v=DMARC1; p=none; rua=mailto:dmarc@... to start

Caveats

• BPA results reflect the last scheduled run; run cipp_run_standards_check for fresh data.
• Standards Remediate mode can change tenant configuration without an additional confirmation — scope carefully and stage Alert first.
• Domain health doesn't catch every email-auth issue (it doesn't validate ARC, BIMI, MTA-STS) — for full mail forensics, supplement with external tools.